Skip to main content

From material estimate to handover: CutOptim + JobOptim

beginner8 min readUpdated: November 15, 2026
Tiled bathroom wall with a window: whole tiles grey, cut pieces numbered
The plan says what you need. The job log shows what got done.

Quick answer

A tiling, paving or roof job loses money in two places: the material order and the disputes. CutOptim’s calculators lay out the tiles, count the cut pieces and turn your own prices into a cost estimate, so the material line of the quote is tighter and the allowance smaller. JobOptim documents the job with photos and dictation, the client follows progress through a link, and the job ends with a handover report.

In a bathroom remodel quote the tile line is often built like this: square footage times the tile price, plus ten percent “to be safe”. During the job, the record is a pile of photos on a phone that someone sorts through at night. This guide walks through the whole chain with two tools: planning in CutOptim, the job in JobOptim, and where a contractor saves time, material and arguments along the way.

What you will learn

  • How the size of a surface becomes an exact material count and order list
  • Why measuring the cutting waste beats a fixed allowance, with measured examples
  • How to document the job and the concealed work in JobOptim
  • How the plan, the quote, the job and the handover fit together
Workflow: plan in CutOptim, quote, the job in JobOptim, the client follows, handoverFive steps. CutOptim: 1 plan (material needs, cutting plan), 2 quote (tighter material and cost line). JobOptim: 3 job (job log, photos, concealed work), 4 the client follows progress by link or QR code, 5 handover with a locked PDF report.CutOptim1. PlanMaterial needs,cutting planCutOptim2. QuoteTighter materialand cost lineJobOptim3. JobJob log, photos,concealed workJobOptim4. Clientfollows progressby link or QRJobOptim5. HandoverLockedPDF reportWorkflow: plan in CutOptim, quote, the job in JobOptim, the client follows, handoverFive steps. CutOptim: 1 plan (material needs, cutting plan), 2 quote (tighter material and cost line). JobOptim: 3 job (job log, photos, concealed work), 4 the client follows progress by link or QR code, 5 handover with a locked PDF report.CutOptim1. PlanMaterial needs, cutting planCutOptim2. QuoteTighter material and cost lineJobOptim3. JobJob log, photos, concealed workJobOptim4. Clientfollows progress by link or QRJobOptim5. HandoverLocked PDF report
CutOptim: planningJobOptim: the job

Why is the usual material estimate off?

“Area divided by tile size, plus ten percent” misses two things. The first is cutting: at the wall edges and around the window and the tub every tile is cut to size, and whether the offcut can be used somewhere else depends on the layout. The second is packaging: tile is sold by the box, pavers by the pallet, lumber in stock lengths. A fixed percentage is too little on one job and too much on the next. Too little, and the tiler stops halfway to reorder, often from a different batch with a different shade. Too much, and the rest ends up in the garage, paid for by the client.

A tighter estimate is not a guess but a layout: the calculator places the surface tile by tile and only then counts.

Step 1: material and cutting plan in CutOptim

The tile calculator takes a floor (a rectangle or an L shape) or a wall, with the window, door or tub as an opening. You pick the tile from manufacturer datasheets: the calculator uses the tile’s real size, the smallest joint and the pieces per box, not the nominal format. Then you choose the pattern (straight, running bond, herringbone or basket weave) and get:

  • a layout in which every cut piece has a number and the tile it is cut from,
  • setting-out dimensions: the bottom edge of the first full row and the first vertical joint,
  • an order list in tiles and boxes, with the breakage reserve.

The paver calculator works the same way with the paving layer: it counts whole pavers and cut pieces, and where two cut pieces come out of one paver it pairs them. Pallets and weight come from the datasheet when the datasheet states them. It does not size the bedding or the base, because those depend on the soil and the load.

The rafter length calculator turns the span, the pitch and the overhangs into every rafter and batten, with their cut angles. Optimize in the app carries the list into Wood mode, where the optimizer spreads the pieces over as few stock boards as possible, section by section.

How much less waste? Measured examples instead of a flat percentage

There is no general “you save this percentage” number, and this guide does not give one. Waste depends on the room, the pattern and the tile, so the calculator measures it. A few measured examples from CutOptim’s own pages:

  • Tile, floor: on a 10 × 8 ft floor with the Daltile Vertuo 12 × 24 in tile and a 3 mm saw cut, a 45° herringbone needs 51 tiles at 18.4 % waste and a ⅓ running bond 48 tiles at 13.3 % (tile calculator, FAQ). Same floor, two patterns: you see the price of the pattern in the quote already.
  • Pavers: on a 20 × 15 ft L-shaped patio in a 45° herringbone with 200 × 100 mm pavers, 3.3 % of the pavers bought go into cut pieces (paver calculator, FAQ). Your breakage reserve goes on top of that, not on top of a guessed ten percent.
  • Roof: on a measured 12 ft shed roof, 16 ft boards wasted 10.7 % of the rafter lumber and 20 ft boards 28.5 % (roof framing cut list).

The lesson is the same in all three: most of the waste comes from decisions (pattern, stock length, starting point), and you see those on the plan before you order, not on site.

A cost estimate for the quote

In the tile and paver calculators you can enter your own price. The estimate prices exactly what the order list tells you to buy: after the breakage reserve and whole boxes. A box price is multiplied by the boxes, an area price by the area in those boxes. The calculator marks this as an estimate, not a quote: it prices only the tiles or pavers, without adhesive, grout, waterproofing or delivery.

That estimate is the basis of the material line in your quote. Because it comes from the layout, you can show where it comes from: the client sees the layout, the cut pieces and the box count. The result downloads as CSV, the paver plan also as a PDF, and the roof plan through Print / PDF.

Step 2: documenting the job in JobOptim

The material arrives, the work starts, and from here JobOptim takes over. It runs on your phone in the browser, with nothing to install. On site, a tap, a few photos and a dictated sentence make an entry, and every entry gets a timestamp. If the signal drops for a short while, the entry waits in a queue and is sent when the connection is back.

What is worth recording:

  • Material: the tile arrived, how many boxes, what is missing. Next to the CutOptim order list you see at once when something is off.
  • Concealed work: the substrate, the waterproofing and the build-up, photographed before tiling. JobOptim’s page for tiling contractors covers what to capture; for patios see the paving page.
  • Change orders: when the client asked and what came of it.
  • Work done: the daily progress, so you are not digging through the gallery at night.

The client follows progress through a link or QR code, with no account, and sees only the entries you mark for them. Internal notes stay internal, and you can revoke the link.

Step 3: handover and a locked report

At the end a PDF report is built from the selected entries, and the finalized version does not change. That is the handover document: what was done, when, and what the work now under the tile looks like. JobOptim’s guide to the job handover and punch list lists what to record at that point.

JobOptim documents the work with photos and timestamps. It is documentation, not a legal certificate; which records are required depends on your contract and local rules.

Both together: where do you save time, material and arguments?

The chain: plan → quote → job → handover. There is no automatic data transfer between the two tools. The CutOptim plan stays your document, and in JobOptim you refer to it in the job’s entries.

  • Material: the order list comes from the layout, not from a flat percentage. The allowance gets smaller, and reorders from a different batch get rarer.
  • Money: the material line of the quote prices what you actually buy, rounded to whole boxes. You are less likely to cover a shortfall out of your own pocket at the end.
  • Time: the layout and the setting-out dimensions are on the plan, and the report builds itself from the on-site entries instead of an evening in Word.
  • Arguments: the client sees where the quantity comes from at the quote, sees the progress during the job, and the concealed layers are on timestamped photos.

CutOptim’s calculators work without an account. JobOptim’s free account works fully for 14 days, no credit card needed; after that you get a quote sized to your team.

Frequently asked questions

What is the difference between CutOptim and JobOptim?
CutOptim is the planning before the job: it works out how many tiles, pavers or how much framing lumber you need and how to cut it. JobOptim is the documentation during the job: a job log with photos and dictation, a progress page for the client and a PDF report. Both products come from the same team.
How much less waste will I have with CutOptim?
There is no single percentage, because it depends on the room, the pattern and the tile size. That is why the calculator measures the cutting waste instead of adding a fixed allowance. In a measured example, a 10 × 8 ft floor with 12 × 24 in tiles, a 45° herringbone needed 51 tiles at 18.4 % waste and a ⅓ running bond 48 tiles at 13.3 %.
Does CutOptim write the quote?
No. The tile and paver calculators turn your own prices into a cost estimate for the quantity the order list tells you to buy. That estimate is the basis of the material line in your quote; labour, adhesive, grout and delivery are yours to add.
Do I need an account for both tools?
CutOptim's tile, paver and rafter calculators work without an account. JobOptim needs its own account; the free account works fully for 14 days, no credit card needed. Your client needs no account to view the progress page.
Does CutOptim send the plan to JobOptim?
No, there is no automatic data transfer between the two tools. The CutOptim plan and order list stay your document; in JobOptim you refer to them in the job's material entries, for example when the tile is delivered.
Is JobOptim a legal record?
JobOptim documents the work with photos and timestamps; it is documentation, not a legal certificate. Which records your contract or local rules require is up to them.

Related

Ready to optimize your cuts?

2 free runs without an account, then 3 a month with a free account

Open App